---
title: "S-IDAP Additional Functions and Settings"
slug: "s-idap-measurement-set-configurator"
updated: 2026-10-27T23:11:52Z
published: 2026-10-27T23:11:52Z
canonical: "ims-handbook.cenosco.com/s-idap-measurement-set-configurator"
---

> ## Documentation Index
> Fetch the complete documentation index at: https://ims-handbook.cenosco.com/llms.txt
> Use this file to discover all available pages before exploring further.

# S-IDAP Additional Functions and Settings

The S-IDAP Details Page header includes several additional functions. Below is an explanation of each function:

## Header Functions![](https://cdn.document360.io/e492a0e0-a4ba-4aca-8fc6-76b95f91fdf3/Images/Documentation/image-5UIB1BZ2.png?sv=2026-02-06&spr=https&st=2026-11-04T22%3A51%3A53Z&se=2026-11-04T23%3A51%3A53Z&sr=c&sp=r&sig=e4K%2Fi2e5zrJnVW6GUY0bYQEYHuOeXbc47OWWNfNcsYw%3D)

### Measurement Set Configurator

Clicking this button opens the configuration measurement set page in the Equipment module. Here, you can perform calculations and change settings in the Measurement Set.

### Show

This option displays the labels below the [Corrosion Rate and Remnant Life Overview plots](/docs/s-idap-overview-plot-tab).

### Calculate

Use this option to recalculate the Corrosion Rates for a selected CML / MP or for a Circuit.

### Arrow Left – Arrow Right

These buttons allow you to scroll to the previous or next Circuit (only works if more than one Circuit is selected). If not, no arrows will show here.

### Settings

![](https://cdn.document360.io/e492a0e0-a4ba-4aca-8fc6-76b95f91fdf3/Images/Documentation/measurement-set-configurator-image-c0ei57ma.png?sv=2026-02-06&spr=https&st=2026-11-04T22%3A51%3A53Z&se=2026-11-04T23%3A51%3A53Z&sr=c&sp=r&sig=e4K%2Fi2e5zrJnVW6GUY0bYQEYHuOeXbc47OWWNfNcsYw%3D)

Skip Commissioning Date: If enabled, the commissioning date and [Nominal Wall Thickness](/docs/long-short-and-baseline-readings) will not be used in the S-IDAP calculations. This is only applicable if a [Base reading](/docs/long-short-and-baseline-readings) is available.

Block Wrong Measurements: If enabled, measurements that you marked as wrong will be skipped.

Prediction Date: Sets the date for which the Wall Thickness will be calculated and displayed in the [TrendPlot tab](/v414/docs/s-idap-trendplot-tab).

**Colour Settings**: Allows you to change the colour settings for the overview plot.

![](https://cdn.document360.io/e492a0e0-a4ba-4aca-8fc6-76b95f91fdf3/Images/Documentation/measurement-set-configurator-image-tqaiizt1.png?sv=2026-02-06&spr=https&st=2026-11-04T22%3A51%3A53Z&se=2026-11-04T23%3A51%3A53Z&sr=c&sp=r&sig=e4K%2Fi2e5zrJnVW6GUY0bYQEYHuOeXbc47OWWNfNcsYw%3D)

Other settings are for tuning parameters for the S-IDAP methodology. Normally the default values should be sufficient.